Инструкция на CoolAir

[pasha56]

Может кто-нибудь поделиться инструкцией на coolair?

[pasha56]

Ну неужели не укого нет!? Подскажите кто знает как нулится эта плата?

[kavlav]

Pins for connectors.
Pins for a 72-contact connector

72-pin connector
pin Side A Side B
1
2 SPEAKER L
3 SPEAKER R GND
4 HOLD1 SW
5 HOLD 2 SW
6 HOLD 3 SW
7 HOLD 4 SW
8 HOLD 5 SW
9 START SW
10 BET ONE SW
11 SELECT GAME SW
12 AUTO START
13
14 MAXBET SW
15 INFO SW
16 FRONT DOOR SW
17 BACK DOOR SW
18 Coin in (Pulse mode)
19
20 STATISTIC SW (short)
21 COLLECT SW
22
23 BILLS COUNTER SELECT GAME LAMP
24 DROP COUNTER WBA LED
25 REMOTE COUNTER UPPER LAMP BLUE
26 GAMES COUNTER UPPER LAMP WHITE
27 HANDPAY COUNTER WIN COUNTER
28 TOKEN COUNTER BET COUNTER
29 HOLD 1 LAMP BET ONE LAMP
30 HOLD 2 LAMP MAXBET LAMP
31 HOLD 3 LAMP COLLECT LAMP
32 HOLD 4 LAMP
33 HOLD 5 LAMP AUTO START LAMP
34 START LAMP INFO LAMP
35
36 GND GND

For connecting the bill acceptor in the impulse regime it is necessary to apply a signal to 18А.

Pins for a 10-contact connector

10-pin connector
pin Side A Side B
1 GND GND
2 GND GND
3 +5v +5v
4 +5v +5v
5 +12v +12v
6 +12v +12v
7
8
9 GND GND
10 GND GND

Plug-in of a bill acceptor
General information
The bill acceptor is connected to the block by means of a special interface cable according to the following table.
RS232 is used for the protocol ID003.
TTL is used for protocol SSP.
It is connected to the connector X3.
COM Port
pin purpose
1 RXD (TTL)
2 RXD(RS232)
3 TXD(RS232)
4 TXD (TTL)
5 ground
6 NC
7 NC
8 NC
9 NC

Initialization:
(IMPORTANT: DO NOT ABRIDGE THE CROSSPIECE “ERASE” - THE PROGRAM WILL BE ERASED)

- while the board is switched on, ground the lead 19А.

- reset the board having abridged the crosspiece RESET

- initialize the memory by any button

- disconnect the lead 19A from the ground

- reset the board, having abridged the crosspiece RESET, the message will appear on the screen on
the red background
- turn the key, the configuration settings will be available after that. On the first page of the settings
currency type and denomination are adjusted. On the fourth page – adjustments of the bill acceptor
channels (in accordance with a sticker on the bill acceptor).


Without initialization of the board at turning the key the following menu is available:
-ATTENDANT
-ACCOUNTING
-DIAGNOSTIC
-EVENT LOG
-GAME HISTORY
-GAME STATICTIC

At turning the key with the door opened (lead 16А to the ground) the following is available:
-GAME SETUP
-MACHINE SETUP
-CALIBRATION


In the menu MACHINE SETUP/PARAMETER SETUP the setting REMOTE INPUT
is a permission or prohibition of the key credit setting.


At the setting REMOTE INPUT switched on the key credit is set as pointed out below:
- turn the key
- press HOLD5 twice
- set the credit with the buttons HOLD3/HOLD4/HOLD5

[hammer_76]

Вот это да! Разработка платы Российская, а инструкция на чистом ангельском без ошибок даже! Молодцы россияки!!!

[pasha56]

Большое спасибо! Теперь мне в тему кто может прошить CoolAir...

[billacceptor]

А я думал что это китайское очередное чудо :)

[Ozzis]

а что - это чудо можно реально ещё и прошить? поделитесь как, а то видел тока на картинках, боюсь у китайцев покупать, они сами толком кроме вышеприведённой инфы нифига не знают и сказать не могут, тока блеют и разводят руками. Я когда спросил о потреблении - мне сказали что я дурак и больше на мои письма не отвечали :)